High-Quality Vintage Tube Distortion effect
The organic sound of a tube amplifier being pushed into breakup has been the gold standard for overdriven and distorted tones for as long as musicians have been intentionally distorting their signals. The gentle natural compression and rich blend of even and odd harmonics produced by analogue tube circuitry make any effected signal feel more powerful, punchy, and alive.
Unlike solid-state transistor and fuzz circuits which only produce odd harmonics and limit the incoming signal in an unnatural and unresponsive way, Redoptor smoothly and dynamically responds to the changes in volume of incoming audio, just like a real tube amplifier. This means that louder sounds are saturated with more crunch and delicious harmonics, while softer and naturally decaying sounds clean up gradually. This creates a very sonically pleasing distortion.
Exact circuit emulation
In addition to its spot-on modelling of hot vacuum tubes being pushed into glorious, creamy distortion, Redoptor packs several features that allow it to accurately mimic the behaviour of a complex analogue circuit with all its interactive and complementary components.
Redoptor’s adjustable tube bias parameter creates subtle amplification of even harmonics and gentle transient reshaping in the signal. Every individual element of the plugin’s signal chain has similarly been designed to capture the subtleties and dynamics of proper high-quality analogue tube distortion.
Completely adjustable preamp
Redoptor expands on classic tube guitar amplifier circuit design by offering total control of the preamp’s frequency range. The cut-off point for both high and low tones may be set before the signal is amplified and distorted, allowing for incredible versatility in sound shaping – from lo-fi to full-spectrum.
While many typical amplifiers and emulations rely on a fixed graphical equalizer offering limited control, Redoptor features a powerful parametric equalizer with independent gain and frequency control of 4 bands.
Independent stereo channel processing
Although based on the mono signal paths of vintage guitar amplifiers, Redoptor is a fully functioning stereo tube distortion with an independent path for each channel in the stereo signal. This allows each side to have completely different harmonics and distortion added to it. So, synth sounds, for example, can benefit from enhanced definition and stereo imaging in addition to the analogue feel offered by the tube distortion emulation.
Dynamics under control
A built-in pre-gain compressor module and master output limiter provide even more freedom to sculpt the perfect saturated sound. These two elements are studio essentials for creative gain staging. The preliminary compressor adds punch and controls your signal’s dynamic range before it hits the highly responsive distortion stage. The master output limiter tames unruly peaks and polishes your signal as it leaves the plug-in.
Redoptor perfectly emulates the behaviour of classic hot-rodded tube guitar amplifier circuits, allowing it to sound just as good as its real-world analogue ancestors.
Guitarists working in the digital realm will feel perfectly at home with Redoptor. Those who have played through an excellent high-gain tube amp will find the plug-in’s warmth, crunch, responsiveness, and singing overtones immediately familiar.
Producers and electronic musicians will also find Redoptor indispensable for the high-quality distortion, rich harmonics, and attitude it brings to their sounds.
Use it to re-amp guitar parts, fatten drum loops, sweeten arpeggiated synths, beef up bass lines, or heat up any sterile audio and you’ll feel the difference from its warm, rich, and truly unique character brings to your music.
- Exact tube and tube's coupled circuits emulation
- Preliminary filters
- Preamp with built-in compressor
- Output limiter
- Fully equipped parametric equaliser
- 64bit internal processing
- Tag-based preset browser
- Two alternative GUI sizes
- MIDI-learn functionality throughout
- Windows 7, 8 or 10
- CPU: 2.0 GHz SSE (Multicore 2.3 GHz recommended)
- RAM: 8 GB (16 GB Recommended)
- Software: VST / AAX compatible host application (32 or 64-bit)
Mac OS X
- macOS 10.7 and later (macOS 11 Big Sur compatible)
- CPU: Intel-based 2.0 GHz (2.3 GHz recommended)
- RAM: 8 GB (16 GB Recommended)
- Software: AU / VST / AAX compatible host application (64-bit only)
Please Note: This is not a standalone program - a host application (DAW) is required to use it.